For permanent application, we recommend using an environmental friendly montage glue to be applied at the area at the back of each panels that is in direct contact with the wall. If a temporary application is needed, we recommend double-sided foam tape.

Because BOCAS 3D bamboo wall panels are a modular products, small seams may occur after mounting the panels on the wall. These seams can be filled using a (paintable) acrylic filler. To avoid cracks in the paint make sure the acrylic filler dries properly before finishing the wall in desired color.In the current and future period of personalized become the mainstream consumer era trend, the mainst...

Yes, you can. Panels are best cut using a knife or a jig saw.For the best result, cut the panels at a point where small irregularities are the least visible. For example, at floor level or where the ceiling begins. If necessary, you can use a fine sandpaper to smooth irregularities at the edges. Any unevenness between cutting edge and wall can be sealed with acrylic.

Once the panels have been attached to the wall and treated with a primer, they can be painted. We recommend a matted water based latex paint, although other kinds of paint (both water and oil based) can be used. Any colour can be applied. Panels can be painted with a brush or a paint sprayer.

Yes, this is possible when using a good quality glue.

Yes, BOCAS 3D bamboo wall panels has had extensive safety testing carried out.The wall panels meet all European standards with regard to; fire safety, water absorption, moisture resistance and expansion rate under various conditions.

Leather wall panels are for interior wall decoration only, it can’t be used in outdoor.

1）It’s direct to hit the nail on the wall surface of the cork. If the wall is flat, don’t need wooden dragon skeleton and waterproofing measures, the walls will not be moldy and rotten, the speed of construction has been greatly improving.2）Bendable, reflect to curved decorative effect (when heat change shape ,the temperature is 83 degrees), 45 degrees stitching and gluing for normal use;3）there i...

If the wall is not flat, then you can use plywood, plywood strips, wooden keel made of substrate mounting.The thickness of the plywood is generally chosen based on the size of the installation area is calculated.Plywood market generally with 5 cm, 9 cm, 12 cm, etc. The greater area selected thicker plywood,general recommendations with more than 9 cm.First plywood installed,then amount the mounting...

Our decorative 3D wall panels are made from natural bamboo fibres from curshed bamboo stalks remaining .this forms the base of this easily installed ECO friendly textured wall panels. total physical processing ,without glue and chemical ,molded to finalize the design by 200-230 high temperaure. the raw amterial used for our dimensional wall panels is 100% recyclable and 100% biodegradable . we h...

We are Alibaba Credit Assurance Suppier,could let both business safey.30% payment in advance,the balance paid against copy of shipping documentsm is standard payment term,but we can also accept D/P,western Union,L/C as per different order situation.

Yes, you can mix different designs in one order, just make sure it is full carton.

No, it is very light, one square meter is around 1.2 -1.8kg. That's why it is easy to install.

Yes, this panel can use in wet country. Just keep the wall not leak. But we do not suggest use in bathroom.This panel can also use in hot place. It is not easy to get fire.It also widely use for South America countries (wet weather) , and Middle East ( very hot area).

Any strong adhesive or glue can be used to stick our 3D wall board,if there is some gapbetween two pcs,you can use putty powder and White latex mixed material. Or use colored m osaic grouting material to fill the gap.

For glue type 3D Plant Fiber wall panel. Any glossy surface without oil,dirt, the best basal material is wood panel.

Delivery time is about 10-15 days as per order qty. such as 500sqm,delivery time is 10 days.

It is natural white color,could be paint any color after installation.Please use water-based paint to paint it.

Panels are installed butt joint way. Joints can be finished with paintable silicone or white woodfiller. And then painted.

We recommend to use solvent based Contact Cement ( Weldwood original formula by DAP or Heavy Duty Contact Cement by Lepage).

Yes, absolutely. You can spray paint the panels with any type of paint. Panels should be primed before painting to create better surface for the paint (just as you'll paint the drywall).

Yes, you can cut the panels. You can use utility knife (make sure you have a new sharp blade) To make a nice straight cut you'll have to slide the blade along the cutting line 3-4 times gradually increasing the pressure.

1.5mm/2.5mm

The 3D panels are made of bamboo pulp. The process is very similar to the papermaking.

ok. Through the heating, the amount of wood can be bent to a certain degree.

And the general wood is different from the wood and plastic surface and the internal material and color is the same, the surface is more bright, so no need to paint wood, with a variety of colors to choose from.

And plastic wood (plastic wood made of 100% plastic) is different, the wood is plastic and wood chips in accordance with the ratio of about 1: 1 made. Because of the natural fiber ingredients, wood has a better anti-UV performance and lower thermal expansion and contraction performance, and easy to work like wood.

The environmental significance of wood-plastic is multiple, on the one hand, it consumes waste plastic and wood powder that pollutes the environment. On the other hand, it can effectively replace the use of wood in the outdoors, thus saving precious natural resources. Because it does not contain any toxic ingredients, it can and other ordinary construction waste to do the same treatment, will not ...

Yes, samples are available for BOCAS. you need to pay for the sample at first, we will send the samples, when you order ,we will deducted sample free.

In our country, the so-called "wood plastic" is the use of recycled plastic and wood chips or rice bran and other natural fibers in accordance with a certain proportion of extrusion and forming a material, that is, wood composite materials (WPC Wood Plastic Composite) Referred to as "wood plastic" or "plastic".

We packed leather Carved Wall panel by Carton Box with Bubble

25-30years

40*40*2.5cm30*60*2.5cm

Dust proof ;Sound proof ;Recyclable ;Fattern flow ;Water proof ;Fire resistant .

Surface : strong fire resistant & water proof PU leather . Middle : polyurethane & sound insulation foam.Base panel : Fire-proofing PVC board.

3D leather panel is beautifully made product. When panels installed they create large-scale three-dimensional walls and ceilings. 3D Faux Leather panels are available in various colors, texture and patterns.All sides and corners are impeccably finished. Panels have 3 layers: top layer - water proof Polyurethane; second layer (filler) – sound/water proof Polyurethane foam; third layer (back board) ...

Modular installation of our own research and development, can be applied to integrated ceiling, can also be used for background, than the traditional soft package installation is simple, mold production, many styles, with flame retardant, noise, comfort, integration, mold, environmental protection advantage.